As taken directly from Eagle Industries:
The Eagle Industries Maritime CIRAS (MAR-CIRAS) is designed to allow the end user to rapidly jettison the armor platform. This aids in ease of use during WMD Decontamination, access to a wounded officer, as well as Maritime Operations.

• Heavy-duty, abrasion and water resistant #1000 denier Cordura® nylon exterior construction
• 1” Mil. Spec. webbing cross straps for mounting MOLLE pouches
• Detachable shoulder pads
• Rear drag handle
• Internal and external cummerbunds for tight, secure fit
• Fully adjustable for height and girth
• Compatible with detachable ballistic accessories: * All sold separately *
BC-STL (Ballistic Collar Protector)
BDP-STL (Ballistic Deltoid Protector)
BGP-STL (Ballistic Groin Protector)
BSP-STL (Ballistic Bicep Protector)

VIEW ALL CIRAS PRODUCTS

1. Place ceramic plate and soft body armor in front and rear vest portions.
2. Lace pull pillow handle stiffener into slot in handle.
3. Feed pull cable to the right or left side of the vest, (opposite of your shooting side), through webbing channel located at the top of the front vest portion. Continue routing pull cable through the webbing channel on the shoulder extension. Pull excess through and secure pull pillow with Velcro cover and strap.
4. Fold Dacron in half, tie an overhand knot in end and slide washer over looped end. Feed looped end of Dacron through grommet located in the inside back portion of vest under protective webbing. Flip vest back portion over and pull looped end of Dacron taut.
5. Slide internal cummerbund through 3” webbing slot on vest back portion. Pull excess through and push Dacron loop through appropriate grommet for sizing. Repeat for opposite side.
6. Slide external cummerbund and through main sleeve. Pull excess through and push Dacron through appropriate sizing grommet.
7. Rout shoulder extension under shoulder slot. Be sure to route shoulder stay with pull cable last. Pull shoulder extension through and push Dacron cord through appropriate grommet. Lace pull cable through Dacron loop. Pull cable should run on top of all adjustment points and be free and clear of any obstructions. Pull release cable taut and feed end into excess retention slat at bottom of vest.
8. Wrap should pad, padded side down, around shoulder strap, secure with Velcro and tuck into shoulder extension slot.
9. Close back flap panel and secure to underbody with snap.
   
   VIEW ALL CIRAS PRODUCTS

Cleaning Instructions:
For normal dirt, use a mild spray cleaner or other mild soap and scrub with a tooth brush as needed. Rinse with cold water and air dry. DO NOT machine dry. ALWAYS AIR DRY.

For heavy dirt, grease or oil, treat with a dry cleaning solvent followed by a spray cleaner or mild soap, Scrub as needed with a tooth brush. Rinse with cold water and AIR DRY.

An occasional spraying of WD-40 or Bees Wax on metal hardware, especially if used around saltwater, will preven corrosion and give your EAGLE gear the durability you deserve.

SPECIAL PRECAUTIONS:
DO NOT use bleach
DO NOT use harsh or excessive amounts of detergent
DO NOT wash in hot water
DO NOT expose to extreme heat
DO NOT put in dryer

WARRANTY PROCEDURES:
I. Eagle Industries warrants each component of the Combat Integrated Releaseable Armor System (CIRAS) against manufacturer defects or against defects in materials or workmanship for a period of twenty four (24) months from the date of manufacture.

II. The warranty is void should a component of the CIRAS be utilized in a manner considered outside the normal course of activities for which the product was designed.

III. The warranty is void should the CIRAS be abused through improper care and maintenance as set forth in the care and cleaning instructions provided with the system.

COMPONENT LIST of the MAR-CIRAS
Vest front portion - 1 each
Detachable Shoulder Pads - 2 Each
Vest rear portion - 1 each
Pull cable and handle stiffener - 1 each
Internal cummerbund - 2 each
External cummerbund - 2 each
Dacron retaining loop and washer - 1 each

VIEW ALL CIRAS PRODUCTS